About Us

Back Issue Index
MAGAZINE
Purpose
Digital Magazines
Sample Articles
Magazine Index
Ready To Travel
Buyer's Guide
Kevin Cameron's Collection
Technical FAQ
Dodge/Cummins History
Classified Ads
Subscribe/Renew
Request Free Issue
Gift Subscription
Buy Back Issues
Buy TDR Logo Items
Advertising
TDR Advertisers
Membership Drive

TSB's for 1995 trucks

Category 2 - Front Suspension

02-05-95	4x4 4x2 Cab Chassis	Rattling/clunk type noise from front of vehicle. Verify that the stabilizer bar is built with the correct ball stud links. If necessary, the bulletin details the replacement of both stabilizer links with tapered ball stud links.
02-01-96A	All	Camper Special service kit. The bulletin supersedes TSB 02-01-96 dated 3/15/96. The bulletin applies to body style codes 31, 32, and 62 with one of the listed GVW sales codes Z2B, Z3A, Z7B, Z8A or Z8B. The bulletin describes the parts and installation procedure for a special service kit developed for use by owners that consistently carry a box mounted camper. A rear stabilizer bar and auxiliary spring comprise the kit.
02-03-96	All	Creaking noise from rear of vehicle. The diagnosis involves the inspection of the rear leaf spring assembly to verify the appropriate number of spring tip inserts are present. If tip inserts are broken or missing the repair procedure is detailed in the TSB.
02-04-96	2wd	Lower ball joint replacement. This bulletin applies only to two wheel drive vehicles. It discusses the service differences in tack welded ball joints/control arms and non tack welded ball joints/control arms.
02-06-96	4wd	Track bar ball joint diagnosis. The bulletin refers to the ‘97 Truck Service Manual and is a supplement to help the technician troubleshoot loose or worn steering components. The track bar ball joint previously did not have an inspection procedure.
02-03-97A	All	Rear of vehicle sits too low. This bulletin supersedes TSB 02-03-97 as there were part number errors in the previous bulletin. The bulletin applies to 1500 series trucks rated at 6400 GVW and 2500 series trucks rated at 8800 GVW. The bulletin discusses rear leaf springs and shock absorber availability that will increase the height of the vehicle when the vehicle is at maximum GVW. The bulletin gives specific part numbers for various applications.
02-06-99	All	Front wheel bearing grease is evident on the bearing seal area. This bulletin supersedes TSB 02-06-99, dated June 11, 1999. The revisions include the addition of 4x2 models and additional model years. This information-only bulletin discusses the fact that front wheel bearings may be incorrectly diagnosed as faulty due to the evidence of wheel bearing grease on the bearing seal areas. This grease purge is a normal design condition. The factory fill of the bearings includes a slightly greater amount of grease than is required for the bearing lifetime lubricant. A portion of the grease purges through the self-venting seal in the initial few thousand miles to form an additional barrier in the area of the seal and the stamped slinger. This barrier aids in the prevention of contaminants passing through the seal and into the bearing. Do not remove or clean the purged grease as part of normal maintenance because it provides additional protection and once removed, damage to the seal and bearing could result.
02-13-99	All	Squeaking noise from rear leaf springs. This bulletin supersedes TSB 02-03-96, dated may 31, 1996. If the diagnosed condition is a squeaking noise coming from the rear of the vehicle, the bulletin gives the correct repair procedure to replace the leaf spring tip liners/install spring clip isolators.
02-04-00 A	All	Squeaking/clicking noise from rear leaf springs. If the vehicle has a squeaking/clicking noise coming from the rear of the vehicle, verify that the noise is coming from the rear springs as the vehicle’s suspension goes through jounce and rebound. If a squeaking/clicking noise is coming from the rear springs, perform the repair procedure. The procedure involves replacing the spring tip liners and installing spring clinch clip insolators.
02-001-01	All	Rear of vehicle sits too high to allow hook up to a fifth-wheel trailer. This bulletin applies to 2500 and 3500 4x4s. The curb hight lowering package is designed to reduce the rear spring spacer block by 1 7/8 inch, which will lower the rear of the vehicle by several inches proving clearance so that most customers can attach their fifth-wheel or goose neck trailer to the trailer hitch turntable.

Category 3 - Rear Axle

03-03-95	All	Rear axle trac-loc chatter. This bulletin supersedes 03-01-94 (7/8/94) and applies to trac-loc Dana model 60, 70 and 80 axles. The symptom is chatter while turning corners. The bulletin involves draining and refilling the axle with new fluid and trac-loc additive. It is important that gear oil 4796517 and trac-loc additive 4318060 be used.
03-02-96	2500 and 3500 4x2 trucks, regular cab, automatic transmission and two-piece propeller shafts	Shudder when pulling away from stop when operated at maximum GVW rating. The bulletin is a supersession of bulletin 16-01-94. If the vehicle exhibits a driveline shudder while pulling away from a stop at maximum GVW rating, the bulletin describes the replacement of the two-piece driveline and center support bracket with a single piece assembly.
03-03-96	With automatic transmission and 5.9 Turbo Diesel engine. Note: ‘96 2500 club cab, 155 WB 4x4 with heavy duty transfer case built after 5/9/96 have the revised propeller shaft.	Droaning noise/vibration. The symptom typically occurs at maximum load and is engine speed specific - 1900 rpm for 4x2 models, 1850 rpm for 4x4 models with the truck in fourth gear and the torque converter clutch locked up. If the problem is identified, a repair procedure involving a revised propeller shaft with a yoke weight damper is described.

Category 5 - Brakes

05-09-95 B	All 4x4 and 3500 4x2 Club Chassis only	Drift left or right under moderate or hard braking. The symptom is a drift right or left during moderate to hard brake applications just short of antilock operation. The condition is more evident with worn brakes. The steering wheel remains straight ahead - truck drifts. The repair is not to correct a condition where the steering wheel moves during the drift. If steering wheel moves, a brake system inspection, according to the service manual, is in order. The repair involves installing shems between the wheel and (2500) hub/bearing assemble, (3500) hub extension as required.
05-02-95	3500 4x4/4x2 2500 4x4	Front brake noise on trucks with 86 mm diameter caliper pistons. The symptom is a squeal noise when applying the brakes for a normal stop. The repair involves grinding or filing a chamfer on both ends of the front brake pads.
05-14-95 A	All	Brake pedal noise when depressed. The symptom is a squawk type noise when the brakes are depressed. The repair involves installing a revised back-up plate into the brake combination valve.
05-02-96 A	2500, 8800 GVW -sales code and 3500 built before 8/5/96	Accelerated brake lining wear, front versus rear. The bulletin supersedes TSB 05-02-96 dated 2/23/96. The bulletin adds the 3500 series truck and incorporates the use of revised brake linings. The bulletin discusses wear conditions. The repair procedure involves replacing possibly the front brake linings, rear brake linings, or rear wheel cylinders, depending on truck model and vehicle sales code.
05-08-96	All	Brake pedal rattle. If a rattle is heard coming from the brake pedal area and is eliminated when pressure is applied to the side of the brake pedal, a repair procedure involving a “wave washer” is outlined.
05-09-96	All	Brake noise. The information only bulletin describes the normal noises that may occur with a properly operating system, ABS self check, trace squeak, grinding, groaning etc., noises are discussed.
05-10-96	All	Chassis dynamics diagnosis. The bulletin discusses conditions where-by the vehicle may move to the right or left when not controlled by the driver. Several causes are cited (aftermarket wheels, road crown, cross winds, incorrect tire pressures, worn wheel bearings, etc.). Diagnosis involves testing the vehicle to determine if the drift is brake related. A brake system evaluation is outlined. Steering and suspension inspection is discussed. Suspension torque values for fasteners are discussed. A suspension geometry evaluation is outlined. Front end alignment specifications are provided. Wheel shim kits and installation of shims for 4x4 trucks is discussed.
05-03-97	All	Chassis dynamics diagnosis. The bulletin supersedes TSB 05-10-96 as revisions have been made to torque specifications and procedures. The bulletin summarizes different conditions that can cause a vehicle to move to the right or left when not controlled by the driver. A lengthy test procedure is outlined to isolate the cause of vehicle drift.
05-04-97	All	Accelerated brake lining wear, front versus rear. This bulletin supersedes TSB 05-02-96A as the bulletin incorporates the use of revised brake linings for trucks with 80mm calipers (typically found on 2500, 4x2 trucks). The bulletin discusses wear conditions, repair procedures, part numbers and rear brake adjustment procedures.
05-11-99	All	Revised power brake booster check valve. This bulletin applies to vehicles equipped with the 5.9L Cummins diesel engine. A revised power brake booster check valve p/n 05011393AA has been released for service. The new check valve performance has been improved by changing the flapper style check valve to a spring loaded style check valve. The spring loaded style check valve performance is superior, especially in vehicles that utilize mechanical vacuum pumps to provide the vacuum source to operate the power brake booster. Part number 05011393AA should be used any time the power brake booster check valve is serviced on the subject model vehicles.

Category 6 - Clutch

Category 7 - Cooling

07-07-94	All	Engine slow to warm-up in cold ambient temperatures. The bulletin describes an overcooling condition caused by the thermostat being stuck in a partial open position. Gauge fluction is addressed and is considered normal with no action required. Owners are advised that the cooling system is large to provide capacity and protection for high temperatures and high GCWR ratings. Slower warm-ups are to be expected.
07-03-97	All	Engine coolant usage. This information only bulletin discusses the use of propylene glycol instead of ethylene glycol coolants.

Category 8 - Electrical

08-25-95	All	Power mirror vibration associated with installation of “bugscreen” deflectors. The symptom is blurred images in the power mirrors. The diagnostic procedure - remove the bugscreen. If vibration ceases the mirrors are ok. Bugscreen deflectors are designed to disrupt airflow which can lead to mirror/antenna vibration.
08-24-95	All	Accessory frame ground jumper wire. The bulletin discusses a frame ground jumper wire from the battery negative to the frame bumper bracket be added if electrical accessories (winch, lights, snow plow, etc.) are added to the vehicle.
08-22-95	All	Installation of radio equipment. The bulletin supersedes 08-31-94, 7/15/94 and discusses the proper installation of communication equipment in Chrysler vehicles.
08-16-95 A	All	Speed control - over/undershoot during set of speed selection. The bulletin discusses the “adaptive strategy” that compensates for vehicle-to-vehicle variations in speed control cable lengths. Pressing the “set” button without pressure on the accelerator pedal can cause speed fluctuations. Proper review of the condition with vehicle operator is recommended.
08-41-94	All	Trailer tow brake wire location. An information only bulletin showing the wiring provisions for an electric brake actuator.
08-64-94	All	Power mirror vibration. On vehicles equipped with power mirrors built prior to 9/18/94 this TSB discusses the diagnosis and repair for excessive vibration/blurred images.
08-05-91	All	Trailer tow wiring installation. The information only bulletin gives guidelines for proper wiring of trailer tow wiring packages.
08-23-96	Built prior to 12/15/96	Clicking noise from speedometer. If a clicking/ticking noise is heard coming from the instrument cluster area, the bulletin describes the repair procedure to replace the speedometer.
08-33-96	All	Trailer tow wiring information. Chrysler Corporation has offered optional trailer tow packages on all ‘94 through ‘97 Dodge Ram Trucks and has made trailer tow packages available through Mopar for vehicles that were not built with the trailer tow package. Several changes to the trailer tow wiring have occurred since the truck was introduced. It also identifies flashers. This bulletin identifies the part numbers for the Mopar trailer tow packages required to adapt trailer wiring to a vehicle that did not have the trailer tow package installed as original equipment from the factory.
08-21-97	All	Engine failed to crank — no start. This information only bulletin discusses a condition where the engine does not crank over when the ignition is placed in the start position. The shop should then refer to the appropriate ‘97 Service Manual for proper diagnosis of the starter motor’s electrical circuit.
08-32-97	All	NHTSA authorized airbag deactivation for medical necessity. This information only bulletin describes the procedures necessary to deactivate airbags authorized by NHTSA. Airbag deactivation is a customer pay procedure, not covered under the provisions of warranty.
08-09-98	All	Driver side power mirror vibrates while driving. This bulletin supersedes technical service bulletin 23-39-97, dated June 27, 1997. The problem covered is that the driver side power mirror vibrates or causes blurred images in driver side mirror while driving. If removal of aftermarket bugscreen deflectors does not cure the problem, a procedure for installing a mirror reinforcement bracket is described.
08-16-98	All	Installation of radio transmitting equipment. This bulletin supersedes technical service bulletin 08-22-95, dated May 12, 1995. This information-only TSB is provided to assist in properly installing communication equipment in Chrysler vehicle. This information should be given to any owner inquiring about installing radio transmitting equipment.
08-17-98	All	Airbag on-off switches. This bulletin supersedes technical service bulletin 08-17-98 Rev. B dated September 18, 1998. This information only bulletin is provided to identify the parts and procedures necessary to deactivate airbags authorized by NHTSA. Airbag deactivation is a customer pay procedure.
08-36-98	All	Use of two digit calendar year codes in automotive computers. There has been a great deal of recent media attention regarding the turn of the century (year 2000, Y2K, etc.) and the effect it will have on computers that have used two-digit calendar year coding in their programming. Questions are arising regarding computers used in automotive applications and the effect year 2000 will have on them. Two digit calendar-year codes have not been used in any Chrysler automotive onboard applications and no problems related to use of two digit coding for calendar years are anticipated.
08-37-99	All	Airbag On-Off Switches. This bulletin supersedes technical service bulletin 08-17-98 Rev C, dated December 30, 1998. This information-only bulletin identifies the parts and procedures necessary to deactivate airbags authorized by NHTSA. Airbag deactivation is a customer pay procedure, NOT covered under the provisions of the warranty.
08-11-00	All	Recordable compact discs used in automotive CD players. Some recordable compact disc media, such as CD-R and CD-RW, may not comply with the standard CD format used in automotive CD players. When these CDs are used, customers may encounter error messages skipping, or delaminating of the labels, which can cause an eject failure. It is important to question whether these kinds of CD media are being used. When customers encounter these symptoms, check the system with a known playable CD. The media may not be compatible with some automotive CD players. Replacing or exchanging the CD player will not address these issues.
08-16-00	All	Front door speaker buzz. The bulletin discusses a buss noise coming from the front door speaker(s). The noise may be more noticeable while listening to “talk” radio segments with deep male voices. The repair procedure involves installing a urethane foam pad between the inner door panel and the door trim.
08-010-01	All	Airbag/clock spring service. When servicing any airbag system, it is essential to follow the proper Service Manual and/or Diagnostic Manual procedures for diagnosing, testing, and replacing of any component. Do not use silicone or any other lubricant spray on or near the clock spring. Lubricants are often used in the clock spring area of the steering column to eliminate noise. Any repair that may disrupt the positioning of the steering wheel with the front wheels will require that the clock spring be centered. This includes clock spring replacement, steering column service, HVAC service, steering gear service, and front suspension crossmember service.

Category 9 - Engine

09-10-95

All

Diagnosing oil consumption.
The concern is an operator report of greater than one quart per one thousand miles. Variations in oil level are likely possible if the oil check is performed on a warm engine due to slow drain back from the inline fuel pump. Discuss with customer and assure dipstick is updated to part number 4796874. The correct dipstick increases the safe zone to two quarts versus the early ‘94 vintage dipsticks with only a one quart safe zone.

09-04-95

All

Excessive oil drainage from oil draft (breather) tube.
The bulletin applies only to engines built prior to 12/1/94. It involves replacing the tappet cover with a new sealed version.

09-07-96

All

Fuel injection pump oil supply bushing oil seepage.
If oil seepage is diagnosed, the bulletin describes the repair procedure using a special oil supply and removal tool.

09-003-01

All

Engine oil additives/supplements.
(EOS) should not be used to enhance engine oil performance. Engine oil additives/supplements should not be used to extend engine oil change intervals. No additive is known to be safe for engine durability and can degrade emission components. Additives can contain undesirable materials that harm the long term durability of engines. Generally it is not desirable to mix additive packages from different suppliers in the crankcase; there have been reports of low temperature of low temperature engine failures caused by additive package incompatibility with such mixtures.

09-004-01

All

Engine lubricant.
This bulletin involves 1989-2001 Ram trucks equipped with the 5.9L Cummins diesel engines. This bulletin discusses the recommended oil filters for use with Cummins 5.9L diesel engine.

	Part No	Manufacturer
	05016547AC	Mopar
	LF3894	Fleetguard Stratapore
	LF3552	Fleetguard Microglass
	LF3959	Fleetguard Cellulose
	3937695	Cummins Cellulose
	FL896	MotorCraft Cellulose
	L45335	Purolator Cellulose
	PF1070	AC Delco Cellulose

The information only bulletin was issued to alert the field to problems caused by aftermarket oil filter. For example, neoprene compounds used internally in the manufacture of oil filters not recommended by DaimlerChrysler may seperate from the filter, lodge in the piston cooling nozzle, and cause the engine to fail. THIS IS NOT AN ENGINE DEFECT.

Category 11 - Exhaust

11-05-96	All	Diesel turbocharger diagnostic procedure. This information only bulletin guides the service technician thorough troubleshooting steps to properly diagnosis turbocharger situations. Normal/abnormal noises, oil leakage, acceleration and low boost, are topics discussed in the bulletin.
11-01-97	All	Whine or howl while driving at highway speeds. This bulletin applies to vehicles equipped with the diesel engine option. Some vehicles may experience a whine or howl noise while driving at highway speeds. This noise may be miss-interpreted as turbo whine. After proper diagnosis of the condition the bulletin’s repair procedure involves replacement of the muffler.
11-08-98	All	Turbo Diesel wastegate actuator repair kit. A new kit has been released that will allow technicians to repair turbochargers with failed wastegate actuators.

Category 14 - Fuel

14-07-96	All	Low pressure fuel system diagnostic procedures. Too low a fuel supply to the Bosch P7100 fuel pump can affect performance. Low rpm miss/ instability, white smoke, hard starting, low power may be the result. This bulletin gives the technician additional information to assist in diagnosis of the above problems.
14-07-97	All	Diesel fuel injection pump tampering. This information only bulletin applies to inline fuel injection pumps as found on ‘94 thru early ‘98 model trucks. The bulletin stipulates that there are only a few items on the pump that are serviceable (low idle adjustment, timing adjustment, throttle linkage adjustment, and air bleed procedures). Any other adjustments or modifications are considered tampering. Tampered injection pumps are not warrantable. The bulletin shows the service location where to look for suspected tampering.

Category 16 - Propeller Shafts & U-joints

16-02-95	Auto trans	Droaning noise/vibration. The symptom/condition is a droaning type noise and/or vibration felt in seat track, floor pan or steering column. The noise is worst case when pulling a camper or trailer with significant wind drag. Peak noise level is 1900 rpm for 4x2 trucks 1850 rpm on 4x4 models with torque converter clutch engaged. The repair involves replacement of the propeller shaft.
16-01-94	All	Shudder at start on vehicles with two piece driveshafts operated at near maximum GVW. The symptom is a driveline shudder when pulling away from a stop. As the vehicle is loaded, the driveline angle will change. In the case of maximum GVW, the rear differential may rise above the rear driveshaft center bearing. The alignment could cause a shudder in the driveline. The repair involves replacement of the driveshaft center support bearing bracket and/or driveshaft.

Category 18 - Vehicle Performance

18-29-95 A	Auto trans	Diesel low power/performance specs. The bulletin applies to automatic transmission trucks with a customer complaint of slow acceleration or low power. Performance tests (0-60) are performed and an acceleration table to reference is provided. The bulletin guides the dealership through a series of trouble shooting tests to troubleshoot the low power complaint. Checks for wide open throttle, a low pressure fuel system check, and finally, an injection pump timing adjustment are described.
18-06-98	All	Hard starting diagnosis. This information applies to the 5.9L Cummins mechanically injected 12 valve diesel. The discussion covers hard or no-start diagnosis and repair.
18-07-98	All	Effects of incorrect idle speed. This information applies to the 5.9L Cummins mechanically injected 12 valve diesel. Incorrect idle adjustments (either too high or low) may cause many different customer concerns. The bulletin gives a list of items that explain the condition/symptoms associated with incorrect idle settings along with component checks and specifications to set it properly.

Category 19 - Steering

19-02-05 B	Build date prior to 1/1/95	Clunk or rattle felt in steering wheel/column over rough surfaces or while making a turn. The repair involves performing an inspection of suspension and steering components to assure proper torque. The replacement of the steering column intermediate shaft is described.
19-01-96	All	Clunk or rattle felt in steering column/wheel. The condition is a clunk or rattle in the steering wheel/column during slow turns or stops on some ‘95-’96 trucks. Diagnosis includes a check of all fasteners for the appropriate torque value.
19-05-96	4x4 trucks with sales codes Z8A and Z8B and 4x2 cab chassis (Z3B) built before 5/15/96.	Shimmy after striking a bump or pothole. This bulletin supersedes TSB 19-04-95 (5/12/95). The bulletin discusses a sustaining vibration (shimmy) felt in the front end of the vehicle after striking a bump or pothole. The repair procedure involves replacing the steering damper, replacing the track bar (if necessary) and the addition of an auxiliary steering damper.
19-10-97	All	Steering wander. If when driving on a straight road, a higher than normal steering wheel movement (perceived as excessive play) is required to keep the vehicle going straight or if over-compensating the steering to keep the vehicle from wandering is a condition, the bulletin describes the diagnosis and repair procedure. The repair involves adjustment of the over-center and, if necessary, the worm thrust bearing preload adjustments on the steering gear.
19-16-97	All	Lower steering column noise and/or minor lower steering column movement. This bulletin applies to vehicles built before Dec. 31, 1996 and describes a lower steering column noise and/or minor lower steering column movement. If movement in the steering column is greater than the tolerance, the repair involves adding a “toe plate” (shim) to the steering column.
19-03-99	All	Steering slow to return to center. This bulletin supersedes technical service bulletin 19-01-94, dated January 28, 1994. This bulletin applies to 4x4 vehicles equipped with a Dana model 60 front axle (sales code DRD). The rate of steering return to center (after turning a corner) may be slower than normal or may require slight steering wheel correction while driving straight ahead. The repair involves performing a ball joint tightening sequence.
19-04-00	All	Squeaking/creaking sound in steering column while turning. This bulletin applies to vehicles equipped with non-tilt steering columns. A squeaking/creaking sound may be heard coming from the area of the steering wheel while turning. The sound is associated with rotation fo the steering wheel or may be heard while going over bumps in the road. The repair involves installing new lock housing attaching screws.
19-005-03	All	Power steering fluid usage. The factory fill power steering fluid for most 2004 model year Chrysler Group vehicles is ATF+4 (part number 05013457AA/S9602) and it provides superior performance at both low and high temperatures. Refer to the table to identify factory fill and the approved service power steering fluid by year and model. From the table it is noted that the �94 to �02 truck uses part number 04883077/MS5931. MS9602 should not be mixed or used as a "topping off" fluid on systems requiring MS5931.
19-005-03	All	Power steering fluid usage. The factory fill power steering fluid for most 2004 model year Chrysler Group vehicles is ATF+4 (part number 05013457AA/S9602) and it provides superior performance at both low and high temperatures. Refer to the table to identify factory fill and the approved service power steering fluid by year and model. From the table it is noted that the �94 to �02 truck uses part number 04883077/MS5931. MS9602 should not be mixed or used as a �topping off� fluid on systems requiring MS5931.

Category 21 - Transmission

21-02-95	Build date after 3/20/95	Quick connect removal and reconnect procedure. The bulletin is an “information only” bulletin outlining two ways to disconnect the quick connectors of the automatic transmission lines.
21-03-95 A	All	Automatic transmission cold temperature cooler bypass kit. The condition occurs at ambient temperatures of -15°F or below. Vehicles equipped with automatic transmission coolers may experience a lack of fluid flow to the transmission due to restricted cooler lines. In periods of extended driving transmission failure may result. The bulletin describes the installation of a cold weather transmission cooler by-pass kit. Caution is needed as the kit decreases the cooling capacity of the transmission when driving in hot ambient temperatures, and is not recommended.
21-04-95	Auto trans	Vibration or perceived engine miss. The symtom is a vibration or perceived engine miss at approximately 1100 rpm as the torque converter clutch engages. The condition occurs in fourth gear lock-up at speeds between 42 to 48 mph. Depending on year model the powertrain control module is either replaced or reprogramed.
21-05-95 A	Auto trans	Delayed transmission engagement/torque convertor drainback. The condition is delayed transmission engagement of 2 to 8 seconds at initial start-up. The problem is most noticeable after the vehicle has been parked for an extended period. The bulletin describes the installation of transmission lines with a one-way drainback valve.
21-08-95	All	Speed sensor oil seepage. The bulletin describes how oil seepage can occur in the speed sensor area. The repair is the installation of a speedometer adapter.
21-09-95	Manual trans	Servicing of 5th gear mainshaft nut on NV 4500 manual transmission. The information only bulletin describes the replacement of the 5th gear main-shaft nut with a new nut if the original nut has to be removed. Under no circumstances is the original part to be reused. Special Mopar lock seal should be applied to the threads at reassembly.
21-24-94	Auto trans	Shift linkage adjustment. The information only bulletin explains how to correct a PRNUL misalignment.
21-15-96	All	Quick connect removal and reconnect procedure. The information only bulletin describes the repair procedure for removal/reconnect of the transmission cooler line fitting on trucks built after 3/20/95 and superseded bulletin 21-02-95, 3/ 31/95.
21-10-98	Manual trans	Loss of fifth gear. This bulletin supersedes technical service bulletin 21-10-98, with an effective date of September 11, 1998. This bulletin applies to vehicles equipped with a NV 4500 manual transmission and the 8.0L V10 gas engine or the 5.9L Cummins diesel engine. The problem described is that the transmission operates normally through all ranges except fifth gear. The 14 page bulletin describes the proper repair procedure.
21-006-01	Auto trans	Automatic transmission fluid usage ATF+4 (Type 9602). This information only bulletin supersedes technical service bulletin 21-16-99, date October 22, 1999. The bulletin discusses a new transmission fluid (ATF+4 - Type 9602) which has been developed and is being used as factory fill for all vehicles with Chrysler automatic transmissions. Until now, vehicles originally filled with ATF+2 or ATF+3 were to be serviced with ATF+3. Effective immediately, it is recommended that all vehicles with Chrysler automatic transmissions except for 1999 and earlier minivans be serviced with ATF+4. ATF+3 should continue to be used for 1999 and earlier minivans because of the potential for torque converter shudder during break in. For all other applications the ATF+4 fluid offers significant benefits as outlined below. ATF+4 must always be used in vehicles that were originally filled with ATF+4. Service intervals do not change. The service interval currently in effect for a given vehicle should continue to be followed. ATF+4 is compatible with ATF+3 and can be used to top off vehicles that currently have ATF+2 or ATF+3. Do not use ATF+2 or ATF+3 to top off vehicles that have ATF+4 fluid. Benefits: Better wear properties Improved rust/corrosion prevention Controls oxidation Eliminates deposits Controls friction Retains anti-foaming properties Superior properties for low temperature operation Mopar ATF+4 is a World Class Fluid having exceptional durability. However, the red dye used in ATF+4 is not permanent; as the fluid ages it may become darker or appear brown in color. ATF+4 also has a unique odor that may change with age. With ATF+4 fluid, color and odor are no longer indicators of fluid condition and do not support a fluid change.
21-009-03	All	Automatic transmission diagnostic teardown procedure. This bulletin provides a procedure to determine repair versus replacement of an automatic transmission assembly.
21-008-06	All	Automatic transmission diagnostic tear down procedure. This bulletin supersedes technical service bulletin 21-018-05, dated October 4, 2005. This information only bulletin provides a procedure to determine repair versus replacement of an automatic transmission assembly.
21-010-06	Auto	Automatic transmission fl uid usage ATF+4 (Type MS9602). This bulletin supersedes technical service bulletin 21-004-04, dated March 16, 2004. ATF+4, type 9602, is being used as factory fi ll for Chrysler Group automatic transmissions. ATF+4 is recommended for all vehicles equipped with Chrysler Group automatic transmissions except for those noted: AW-4 transmissions, Sprinter transmissions, Crossfi re transmissions, MK/PM vehicles equipped with Continuously Variable Transmission (CVT). ATF+4 is backward compatible with ATF+3, ATF+2, and ATF+. Additionally, ATF+4 can be used to top off vehicles that used ATF+3, ATF+2, or ATF+. Benefi ts: Better anti-wear properties Improved rust/corrosion prevention Control of oxidation. Elimination of deposits Control of friction Retaining anti-foaming properties Superior properties for low temperature operation Mopar ATF+4 has exceptional durability. However, the red dye used in ATF+4 is not permanent; as the fl uid ages it may become darker or appear brown in color. ATF+4 also has a unique odor that may change with age. With ATF+4 fl uid, color and odor are no longer indicators of fl uid condition and do not necessarily support a fl uid change.
21-003-07	All	Automatic transmission diagnostic tear down procedure. This bulletin provides a procedure to determine repair versus replacement of an automatic transmission assembly. Follow the proper repair procedure based on the transmission type. This procedure is to be used after the transmission has been removed from the vehicle. This bulletin supersedes technical service bulletin 21-008-06, dated 04/08/06.
21-014-07	All	Automatic transmission fl uid usage ATF+4 (Type MS9602). This bulletin supersedes technical service bulletin 21-010-06, dated 4/16/06. ATF+4, type 9602, is being used as factory fi ll for Chrysler Group automatic transmissions. ATF+4 is recommended for all vehicles equipped with Chrysler Group automatic transmissions except for those noted: Sprinter transmissions, Crossfi re transmissions, MK/PM vehicles equipped with Continuously Variable Transmission (CVT) all vehicles equipped with a A568RC transmission (sales code DG3), all vehicles with a Gentrag MP56 (sales code DG5), and Grand Cherokee�s with the diesel engine option. ATF+4 is backward compatible with ATF+3, ATF+2, and ATF+. Additionally, ATF+4 can be used to top off vehicles that used ATF+3, ATF+2, or ATF+. Benefits: Better anti-wear properties Improved rust/corrosion prevention Controls oxidation Eliminates deposits Controls friction Retains anti-foaming properties Superior properties for low temperature operation. Mopar ATF+4 has exceptional durability. However, the red dye used in ATF+4 is not permanent; as the fl uid ages it may become darker or appear brown in color. ATF+4 also has a unique odor that may change with age. With ATF+4 fl uid, color and odor are no longer indicators of fl uid condition and do not necessarily support a fl uid change.
21-021-08	All	Automatic transmission diagnostic tear down procedure. This bulletin provides a procedure to determine repair versus replacement of an automatic transmission assembly. Follow the proper repair procedure based on the transmission type. This procedure is to be used after the transmission has been removed from the vehicle.

Category 22 - Wheels & Tires

22-03-95	All	Match mounted tire/wheel combinations. The bulletin is an “information only” bulletin describing a match mounting process to improve ride characteristics.
22-04-95	All	Spare tire winch operation. The bulletin is an “information only” bulletin reminding not to use power tools to drive the spare tire winch.
22-05-95 A	Code WDC wheels	Wheel runout measurement code WDC wheels procedures. The bulletin gives the allowable remount and informs the dealer that the tire must be dismounted to correctly measure radial and lateral runout.
22-06-95	All	Match mounting during wheel service. The information only bulletin helps dealers match mount wheels and tires. Premature rust on chrome wheels.
22-01-97	All	Tire and wheel runout. Radial runout is the vertical distance between the high and low points on the tire or wheel edge measured at the center line of the tread. Lateral runout is the horizontal movement of the tire or wheel measured near the shoulder of the tire. Runout of more than the preferred specification may cause the vehicle to shake. This information only bulletin provides the proper specification for runout.

Category 23 - Body

23-68-94	All	Glue seeps out at backlight or windshield moulding. Hot melt glue (clear to light brown) can seep out at the edge of the light or molding. The repair is to clean the glue with Mopar Concentrated Windshield Washer Solvent.
23-71-94	All	Tailgate latch handle loose. The bulletin applies to vehicles built from 8/30/94 to 9/8/94. The hole in the tailgate was stamped oversize. Inspect the latch handle and apply Mopar Bond-All Gel Adhesive to correct.
23-95-94 A	All	Front seat cover wear through above the recliner pivot. The condition is wear-through at the recliner pivot. Inspect as directed and repair if necessary.
23-101-94	All	Anti-friction tape on A-pillar. Bulletin 23-36-94 described a squeak and paint abrasion at the door to windshield A-pillar area. Anti-friction tape is now being applied at the assembly plants to prevent the problem. Do not remove the anti-friction tape.
23-01-96	All	Replacement cargo box information. This information bulletin list the revised part numbers for the 6.5 ft. and 8.0 ft. cargo box with a reinforced front box floor.
23-02-96	All	Creak or tick noise from right side instrument panel. The noise can be reproduced by pushing on the instrument panel at the shelf above the glove box door. The repair involves the removal of a 3/10 rivet.
23-21-96	All	Tailgate difficult to close in cold weather. At less than 5° F the tailgate latch stop bumper may be too stiff to allow for easy closure. Inspect and replace bumper stop.
23-29-96	All	Tailgate cracking on top inner ends. Some vehicles may exhibit a sheet metal crack along the top inner ends of the tailgate. The bulletin describes the parts and the correct repair procedure.
23-45-96	All	Instrument panel creak. This bulletin supersedes TSB 23-57-93, 8/8/93. A creak or squeak may be present on the left or right side of the instrument panel. The noise is caused by two sheet metal parts rubbing together. The repair involves loosening the instrument panel and providing additional clearance between the cowl and instrument panel support joint.
23-46-96	All	Rattle in door area. Inspect the area of the door latch face around the lower window channel retaining bolt. If necessary perform the outlined repair procedure.
23-03-97	All	Difficult to clean light colored “chalky” residue from black plastic body components. The discussion covers difficult to clean light colored “chalky” residue from exterior plastic body components that are molded in black, especially those that are textured, such as door handles, mirrors, roof rack attachments, etc. Frequently, this “chalky” residue is actually an accumulation of car wax, road grime, etc. trapped in the plastic grain. The correction is to clean the component with a soft bristle brush and mild detergent (liquid dish soap) until the residue is gone.
23-22-97	All	Driver’s side wiper blade contacts A-Pillar. This bulletin applies to vehicles built before Oct. 15, 1996. If the driver’s side wiper blade contacts A-Pillar or a popping sound can be heard when the driver’s side wiper blade reaches its full upper wipe position (farthest to the left) during high speed wiper operation, this bulletin describes the repair procedure. The repair has the dealership replace the wiper blades with a blade that has a revised air deflector.
23-27-97	All	Water leaking through rear window. The problem is water leaking past rear window module into cab of vehicle. The bulletin outlines the repair procedure.
23-39-97	All	Driver side power mirror vibrates while driving. This bulletin supersedes TSB 08-64-94, dated 11/4/94. The condition covered in the bulletin is one where the driver side power mirror vibrates causing blurred images in driver side mirror while driving. The repair involves installing a power mirror support bracket onto the driver’s side mirror
23-61-97	All	Noise coming from cargo box area. The problem is an “oil canning” noise complaint coming from the box area caused by the cargo box cross member contacting the vehicle’s frame as the vehicle is operated over a rough-surfaced road. The repair involves installing isolators on two cargo box cross member rails.
23-17-98	All	Center armrest driver side hinge cover broken. If the center armrest upper inertia latch cover (driver side hinge cover) is broken, the proper repair involves replacement of the hinge.
23-35-98	All	Door trim panel retainer clip attachment breakage when door trim panel is removed for service. The bulletin cautions the dealer that damage to the door trim panel may occur if the door trim panel retainer clips are separated from the door without using a trim panel removing tool.
23-08-99	All	Instrument panel creak. This bulletin supersedes technical service bulletin 23-45-96, dated August 2, 1996. A creak or squeak may be present near the left and/or right side(s) of the instrument panel. The noise is caused by the sheet metal joint between the A-pillar and the dash panel plenum lower rubbing together. This bulletin describes the repair procedure which involves loosening the instrument panel and providing additional clearance between the A-pillar inner panel and dash panel.
23-22-99	All	Rattle in door area. This bulletin supersedes technical service bulletin 23-46-96, dated August 2, 1996. Customers may complain of one or more of the following symptoms: rattle heard in the door area; door window shakes when closing; door lower window channel bolt has pulled through the door sheet metal; door sheet metal is cracking around the lower window channel bolt. This bulletin involves removing the window channel from the door and installing a revised window channel.
23-35-99 A	All	Child seat tether anchors. This bulletin supersedes technical service bulletin 23-35-99 dated September 3, 1999. This bulletin identifies the parts and labor operation numbers necessary to install a child seat tether anchor.
23-19-00	All	Instrument panel creak. A creak or squeak may be present near the left and/or right side(s) of the instrument panel. The noise is caused by the sheet metal joint between the A-pillar and the dash p0anel plenum lower rubbing together. The repair involves loosening that instrument panel and providing additional clearance between the A-pillar inner panel and dash panel.
23-014-06	All	Windshield wiper blade maintenance. Windshield wiper blades/elements are frequently replaced unnecessarily. If the wipe pattern appears to be streaky or if there is chatter and no damage to the wiper blades/elements is obvious, the following steps should be performed: Use a soft cloth or sponge and squeegee and a solution of 50/50 alcohol and water, to wash the windshield. Raise the wiper blades off the glass and clean the wiper blade elements with a solution of 50/50 alcohol and water and a soft cloth, paper towel or sponge. Return the wiper blades to their normal operating position. If the wipe pattern is still objectionable, repeat several times. If the wipe pattern is still objectionable, replace the wiper blades/elements.

Category 24 - Air Conditioning

24-06-95 A	All	Odor from air conditioning ducts. Some vehicles may emit a “musty” odor from the airconditioning ducts. The odor is most noticable when the A/C system is first turned on. Two possible causes are discussed and repair procedure are outlined based on less than or greater than 12 months in service.
24-08-95	All	White flakes from instrument panel outlet. Sodium silicate is used to coat the air conditioner evaporator for corrosion protection. If excessive amounts are applied during the manufacturing process, there is a tendency for the extra coating to flake off. Flakes may blow from the vents when the fan is turned on. The bulletin is issued for information only.
24-17-94	All	A/C evaporation freeze-up or lack of cooling on cycling clutch of air conditioning system. Loss of A/C airflow and/or cooling while the blower fan continues to operate may occur. This bulletin discusses the role of the powertrain control module in the A/C system. The electrical signal from the A/C cycling clutch switch passes through the Powertrain Control Module (PCM) to engage and disengage the A/C clutch relay. If the PCM is not properly disengaging the A/C clutch via the relay, the compressor will stay on continuously and result in evaporator freeze-up. Also, the PCM may not energize the A/C clutch relay at all. THis condition results in the lack of cooling from the A/C system. The PCM should be checked per the procedure in the appropriate Powertrain Diagnostic Procedure Manual. Diagnostic Trouble Code 33 (A/C clutch relay circuit) will be present when either of these conditions are caused by the PCM. It is important to perform the complete test sequence because there are other A.C clutch relay circuit components that could also cause or contribute to the condition.
124-01-96A	All	Heater A/C system changes mode to defrost when accelerating. This bulletin supersedes TSB 24-01-96 (2/2/96). The vacuum supply line to the Heater A/C system may drop when accelerating or when speed control engages. This may cause the vacuum motor to switch to defrost. The repair involves the addition of a vacuum check valve to the vacuum system.
24-16-96	With engine serial number 56230585 thru 56293178 or 45232867 thru 45360437. These engines were installed before 6/1/96.	Vacuum system contaminated with engine oil. Some Turbo Diesel trucks were produced without a check valve on the vacuum pump. Without a check valve oil may enter the vacuum system. A visual inspection of the HVAC system is presented and the repair procedure outlined.
24-11-97	All	A/C evaporator odor. This bulletin supersedes technical service bulletin 24-06-95A, dated 5/26/95. Some vehicle operators may experience a musty odor from the A/C system, primarily at start up in hot and humid climates. This odor may be the result of microbial growth on the evaporator core. During normal A/C system operation, condensation forms in and around the A/C evaporator. When airborne pollutants mix with this condensation, bacteria and fungi growth begins and odor results. The repair involves cleaning the evaporator with Mopar aerosol cleaner.
24-009-02	All Chrysler group products using R-134A refrigerent	A/C system leak detection. Vehicles from the factory no longer have leak detection dye in the A/C system. To determine the source of a R-134a leak, a leak tracer dye has to be injected into the A/C system.
24-003-03	All Chrysler group products	A/C system additives. The use of A/C system sealers may result in damage to A/C refrigerant recovery/evacuation/recharging equipment and/or A/C system components. Many federal, state/provincial and local regulations prohibit the recharge of A/C systems with known leaks. DaimlerChrysler recommends the detection of A/C system leaks through the use of approved leak detectors available through Pentastar Service Equipment (PSE) and fluorescent leak detection dyes available through Mopar Parts. Vehicles found with A/C system sealers should be treated as contaminated and replacement of the entire A/C refrigerant system is recommended.
24-003-03	All	A/C system additives. The use of A/C system sealers may result in damage to A/C refrigerant recovery/evacuation/recharging equipment and/or A/C system components. Many federal, state/provincial and local regulations prohibit the recharge of A/C systems with known leaks. DaimlerChrysler recommends the detection of A/C system leaks through the use of approved leak detectors available through Pentastar Service Equipment (PSE) and fluorescent leak detection dyes available through Mopar Parts. Vehicles found with A/C system sealers should be treated as contaminated, and replacement of the entire A/C refrigerant system is recommended.

Category 25 - Emissions

Category 26 - Miscellaneous

26-04-94

All

Diagnostic procedure manuals.
The bulletin gives a current list of available diagnostic procedure manuals. These manuals provide system information, step-by-step trouble shooting procedures, diagnostic and driveability tests, along with diagrams, illustrations and helpful charts to find and fix problems on Chrysler Corporation vehicles. These manuals can be ordered by calling 1-800-626-1523.

TDR Magazine and Website's Purpose